Chendrashaker's World
In this blog most of what I share reflect my efforts to think globally and act locally.
Saturday, July 14, 2012
Saturday, May 5, 2012
Locating the Wicked Leak
Early last winter I began to notice that the water pump was turning on about every 30 minutes so added it's repair to my "to do" list, but have procrastinated to do any thing about it. In January, with the help of my brother we pulled the well pump and replaced a defective checkvalve.
Since I am a light sleeper after 2 am and the "clicking" on/off water pump switch is in the basement below our bed room I could now hear the pump clicking on every 20 minutes. We pulled the pump again to check for leaks and even pressurized the line from the well head to the check valve and the pressure held! The in well line was not the source of the leak.
At the ground surface there were no wet areas that would indicate a leak. I started isolating various lines within the house - the pressure holds. Isolated the pressure tank - the pressure holds.
Next I thought about the hydrant into the log barn and dug it out.
"All right!" I said to my self. I am going to cut the water line to the barn and pond hydrants. So I dug a 4th hole to find the juction of the main water line and branch to the barn/pond hydrants. I cut the line and "walah!" ... the pump was still clicking on every 20 minutes. What!!#@*!!!
I dig out the well head and expose the branch line to the garden hydrant.
The "wikileak" is in this line. It's repair will involve digging up the hydrant and starting there to seal the leak.
Since I cut each branch line from the main water line I decided to install a shut off valve that I can open/close using a long handled extension to isolate, locate and repair future leaks should they occur.
Ahh! ...problem solved or was it?
Since I am a light sleeper after 2 am and the "clicking" on/off water pump switch is in the basement below our bed room I could now hear the pump clicking on every 20 minutes. We pulled the pump again to check for leaks and even pressurized the line from the well head to the check valve and the pressure held! The in well line was not the source of the leak.
At the ground surface there were no wet areas that would indicate a leak. I started isolating various lines within the house - the pressure holds. Isolated the pressure tank - the pressure holds.
So where is this 'wikileak'???
After a few more months and recovery from my burned foot (See blog entry for April 1st "Amputation" ), I decided to become a mole, grave digger, or just a crazy man with a round pointed shovel and find this "wicked leak". Our water line from the well has two branch lines to a hydrant near the garden and another at the barn/pond. I've never been very confident in my plumbing of the pond side hydrant, so I dug holes there first. No leak here that I could see.
Two 4.5 ft holes at the pond hydrants. The water table is only 4 ft down here. ...remind you of WWI? |
Hole to log barn hydrant ...still no leak?! |
"All right!" I said to my self. I am going to cut the water line to the barn and pond hydrants. So I dug a 4th hole to find the juction of the main water line and branch to the barn/pond hydrants. I cut the line and "walah!" ... the pump was still clicking on every 20 minutes. What!!#@*!!!
The 4th hole at the junction of the main line an line to the barn/pond hydrant. |
Okay ... so now what?
Is the "pitless" at the well head leaking?
Is the most recent hydrant set by the garden leaking?
I dig out the well head and expose the branch line to the garden hydrant.
Main water line and branch to garden hydrant. |
Well head. Hole #5. (It only took me 1.5 hours to dig this 2.5x6x5 ft hole ...need a grave anybody? -or- maybe my own!) |
Since I cut each branch line from the main water line I decided to install a shut off valve that I can open/close using a long handled extension to isolate, locate and repair future leaks should they occur.
Brass shut off valve cased in using cinder blocks. |
PCV pipe will allow a 5' handle to open/close the shut off valve to branch lines. |
Well head and shut off pipe. |
...so what if I had installed shut valves on each branch line during the original construction?
Tuesday, April 17, 2012
Peas On Earth, With Good Compost to Amend!
Sunday, April 1, 2012
Amputation
Below are several pictures of the burned foot.
They are not pleasant to look at, so viewer beware.
4 hours after the hot water burn |
24 hours |
36 hours |
Now two weeks later I would like to give blog followers an update.
After five days of self treating I went to the emergency room at our local hospital. The ER physician treated the wound and insisted that I contact the burn unit at the University of Rochester's Strong Hospital.
As you can see the burn was a very serious burn and because I had waited over a week to seek medical help the foot was amputated just above the ankle...Yes, AMPUTATED!
...read on!
April Fool's!
OKAY ... so what really happened?
I did seek medical help from the Krasser Burn Unit at Strong Hospital in Rochester, where Dr. Bell and his staff using general anesthesesia:
1. debrided the granular tissue forming in the central 3rd degree burn area of the foot.
2. took a partial skin graft (a 2x4 sized segment) from my upper thigh and attached it to the 3rd degree burn area of the foot. A very high tech vacuum pump drained any liquids from the wound as well as providing negative pressure to secure the graft to the sub-dermis, insuring a good generative dermis to dermis contact for optimal growth.
7 days post burn/pre-skin graft. You can see the 3rd degree burn (whitish tissue) in the central area. |
I changed the wound dressing each day.
You can see the healing progress in the next few photos.
The skin graft site on my upper thigh. Doctors wanted the graft covered and open to the air so that a dry scab would form where it will crumble off with time. |
Monday, March 12, 2012
Accidents
Last Friday my wife dropped me off south of Hammondsport, NY to backpack along the Finger Lakes trail to Ithaca, NY, 85 miles east by the Finger Lakes Trail. I was making good progress each day, braving snow squalls and some cold night in shelters along the trail. With three days of trekking and 60 plus miles under my belt I was feeling confident about finishing the remaining 22 miles on the last planned hiking day.
Below are a couple of short video clips that give you a brief appreciation of trail hiking.
(Turn up your sound.)
Friday - 3/9 on the trail above Hammondsport.
It's Spring!
Steep trail.
Saturday evening at the Roger's Hill Lean-To, after 27 miles of backpacking for the day; I was fixing myself a cup of hot soup, very pleased with my progress and only one more day before reaching my goal "pull out" point of Ithaca, NY. As I was pouring the boiling water into a my cup the pot jiggled loose from the handle spilling boiling water onto my sock covered foot. I immediately pulled the sock off and poured cold water on the injury.
Too late the damage was done and the hike was over.
(Fortunatly with the warm evening a local ATV rider was able to help transport me to a rendezvous spot where my wife could pick me up.)
...so here I sit dispite all the rational thoughts; trying to sort this out in my mind to bring some closure to this issue.
Why !!?
Accident - Any unpleasant or unfortunate occurence involving injury, loss, suffering, or death; a casualty; mishap. - as defined by my old Funk & Wagnalls dictionary.
Caution!
... viewer discretion advised.
Friday, March 9, 2012
Top Loading/Bottom Unloading Vermicompost Bin
I have been vermicomposting our kitchen waste for over two years. Originally I converted an old guinea pig box into a worm bin. This worked until I tried removing the finished vermicompost, involving the separation of decomposing layers of kitchen waste in order to get at the finished vermicompost. Red worms also had to be removed by hand and returned to the bin in order to access the finished vermicompost. An entirely too messy process to be taking place in my basement. So this is a rather long post sharing my home made, self designed vermicoposting bin.
If you are still interested, read on.
If you are still interested, read on.
An informal drawing of the homemade, top loading/bottom unloading vermicompost bin on wheels. (click on the diagram to see a larger picture of the drawing) |
The homemade, portable top loading/bottom unloading vermicompost bin. |
The plastic lined bin has a turnable "tickler" rod at the bottom of the bin, enabling finished vermicompost to be unloaded from the bottom of the bin.
|
The trommel screening drum is rotated forward and backwards with the screened vermicompost falling into the sloped collecting tray underneath. Since the vermicompost tickled off the bottom of the bin is quite damp, screening is repeated over several days.
(Double clip on the video picture to see a full screen view.)
I cover the bin with newsprint that allows me to keep the bin open, yet dark
for worm activity. The bin is then covered with a meshed garden cloth.
(Double clip on the video picture to see a full screen view.)
I monitor the bin for odors everytime I walk through the basement. Like any active composting process, success often depends on the WONC ratios (water/oxygen - 1 nitorgen/ 3 carbon ratios) by adding more shredded newspring (adding carbon and/or absorbing water) and stirring to move the contents to a more aerobic (with oxygen) vs anaerobic (with out oxygen = unacceptable odor) condition.
Sunday, March 4, 2012
Gone To Pick Up the Sunday Paper.
I have always liked physical exercise. Back in the 70's and very early 80's I ran competive road races including the Boston Marathon multiple times with fair amount of success. By 2009 - age, time and expense (clothing, shoes, race fees, travel, etc) make walking on local roads the ideal aerobic exercise for me. Sundays are my usual "big" walking days in order to make my weekly goal of 30 miles.
Today's walk shown below is a typical loop, requiring about 4 hours to complete.
The google map marks today's 15.42 mile walking loop. |
Subscribe to:
Posts (Atom)